How to Mount Ring Indoor Cam 2nd Gen: A Simple Installation Guide

Mounting the Ring Indoor Cam (2nd Gen) gives you a clear view while keeping the camera secure. You can place it on a flat surface or attach it to a wall or ceiling, depending on your room and viewing needs.

To mount the Ring Indoor Cam (2nd Gen), choose a suitable indoor location, secure the adjustable mount, attach the camera, and test the view in the Ring app. I’ll cover placement, installation, camera positioning, and setup checks so you can avoid common mounting mistakes.

Key Takeaways

• Choose an indoor location with a clear view and nearby power.
• Secure the mount to a suitable wall or ceiling surface.
• Test the camera angle and settings before finishing.

Choose the Best Placement

I choose a location with a strong Wi-Fi signal, a clear view of the room, and easy access to a power outlet. I also keep the camera away from heat, steam, moisture, and other conditions that could damage an indoor-only device.

Evaluate Wi-Fi Signal Strength

I test the camera’s Wi-Fi connection at the planned location before mounting it. A weak signal can cause delayed alerts, interrupted live video, or failed recordings.

I place the camera near my Wi-Fi router when possible, but I avoid hiding it inside cabinets or behind thick walls. I check the signal in the Ring app after temporarily connecting the camera. If the connection remains weak, I move the camera closer to the router or improve coverage with a compatible mesh system.

I also keep the power cable length in mind. The camera must reach a suitable outlet without placing the cable across a walkway, where it could create a trip hazard or become unplugged.

Select a Suitable Viewing Angle

I position the camera where it can capture the main entry points and activity areas. A corner often provides a wider view of a room, while placing the camera directly across from a doorway can show people as they enter.

I mount the camera high enough to reduce accidental bumps, but I avoid placing it so high that faces become difficult to identify. I tilt the camera to reduce views of ceilings, floors, and nearby walls.

I check the image before drilling. I look for blocked areas caused by furniture, curtains, shelves, or plants. I also keep bright windows and lamps outside the center of the frame when possible, since strong backlighting can make people appear dark.

Avoid Environmental Hazards

I install the Ring Indoor Cam (2nd Gen) indoors and keep it away from moisture, steam, and extreme temperatures. I do not place it near sinks, showers, humidifiers, stoves, radiators, heater vents, or space heaters.

I choose a stable surface or a solid wall or ceiling location. I avoid loose shelves and areas where pets, children, or moving doors could knock the camera down.

I also keep the camera and power adapter away from heat sources and exposed liquids. Before drilling, I check for electrical wires and pipes behind the mounting surface.

Prepare the Camera and Mounting Surface

I choose a stable indoor location, confirm that the camera can reach a power outlet, and check the view in the Ring app. I also keep the camera away from steam, moisture, extreme temperatures, and heat sources.

Gather Required Tools

I gather the Ring Indoor Cam (2nd Gen), its power cable and adapter, the mounting plate, and the included screws and wall anchors. I also prepare a pencil, a Phillips screwdriver, and a drill if the surface needs pilot holes.

For drywall, I use the supplied anchors unless a stud lines up with a mounting hole. For wood, I drive the screws directly into the surface after drilling small pilot holes. I use a level to keep the mounting plate straight, especially when I mount the camera high on a wall or ceiling.

I inspect the mounting area before drilling. I avoid locations near electrical wiring, pipes, heater vents, radiators, stoves, and other heat sources. I also leave enough room to slide the camera onto the plate and adjust its angle.

Charge and Set Up the Camera

I connect the power cable to the camera and plug the adapter into an indoor outlet. The Indoor Cam does not use a removable battery, so I place it close enough to the outlet for the cable to reach without tension or a trip hazard.

Before mounting it, I complete setup in the Ring app. I add the camera to my Ring account, connect it to Wi-Fi, and install available software updates. I then open Live View to check the image and confirm that the camera receives power.

I place the camera temporarily at the planned location and test the view. I check entryways and important areas while avoiding private spaces where monitoring would be inappropriate. I keep the camera indoors and away from steam, extreme heat, and cold.

Mark the Installation Points

I hold the mounting plate against the wall or ceiling in the selected position. I use a level to align it, then mark each screw hole with a pencil. I make sure the plate faces the direction I need before marking the surface.

I check the cable path and outlet location again. The cable should reach without pulling on the camera, blocking a walkway, or hanging where someone could catch it. I also confirm that the camera will have enough clearance to slide onto the plate.

If a stud or solid wood supports a screw, I mark that point and skip the anchor there. For drywall or another hollow surface, I drill the marked holes to the anchor manufacturer’s recommended size and insert the anchors before attaching the plate.

Install the Adjustable Mount

I position the adjustable mount so the camera can capture the intended area without blocking doors, windows, or walkways. I choose the correct fasteners for the surface, tighten them evenly, and check the mount before attaching the camera.

Secure the Mount to Drywall

I use the included mounting plate as a guide and mark the screw locations on the drywall. I check for studs, pipes, and electrical wires before drilling. If no stud lines up with the plate, I use wall anchors rated for the mount and camera’s weight.

I drill pilot holes that match the anchor instructions. I press each anchor into the wall until it sits flush, then place the mounting plate over the holes. I drive the screws straight into the anchors and stop when the plate feels secure. I avoid overtightening, which can damage the drywall or distort the plate.

After securing the plate, I gently pull it away from the wall. It should not shift, tilt, or rotate.

Attach the Mount to Wood or Masonry

For wood, I position the plate over a solid stud or other firm wood surface. I drill small pilot holes, then drive the mounting screws directly into the wood. I make sure each screw enters solid material rather than a thin panel or trim.

For brick, concrete, or other masonry, I mark the holes and use a masonry bit. I insert suitable masonry anchors, then fasten the plate with compatible screws. I remove drilling dust from each hole so the anchors can seat correctly.

I keep the plate flat against the surface while tightening the screws. Uneven contact can leave the adjustable mount loose or make the camera point away from the desired area.

Check Mount Stability

I hold the mounted plate and apply light pressure in several directions. The plate should remain firmly attached without movement, creaking, or visible gaps. If it shifts, I remove the camera and correct the fasteners before continuing.

I slide the adjustable mount onto the plate according to the groove and hook alignment, then confirm that it locks into place. I adjust the viewing angle by hand and tighten any adjustment point that controls the position.

I connect power only after the mount feels stable. I then open the Ring app and check the live view. If the image does not cover the intended area, I adjust the camera angle rather than forcing the mount.

Attach and Position the Camera

I secure the camera to its mount, set the lens toward the area I want to monitor, and keep the power cable free from strain. I also check the live view in the Ring app before I finish, so I can correct the position while access remains easy.

Connect the Camera to the Mount

I place the camera onto the included mounting plate or stand, depending on the setup I chose. I align the camera with the mount and press or slide it into position until it sits firmly. If I mounted the plate to a wall or ceiling, I check that the screws hold it securely and that the surface supports the camera’s weight.

I avoid forcing the camera into place. The mount should connect smoothly, and the camera should not wobble after I attach it. I leave enough space around the camera to adjust its angle and reach the privacy cover, reset controls, or cable connection when needed.

Adjust the Camera Angle

I open the Ring app and view the camera’s live feed while I adjust its position. I aim the lens at the main area I want to see, such as an entryway or room, while keeping the image level. I avoid pointing the camera directly at bright windows or strong indoor lights, which can reduce image detail.

I tilt the camera until the view includes the needed floor and background without showing too much ceiling. I then check the edges of the image for blocked areas. If the camera uses a screw or adjustment joint, I tighten it after choosing the angle so the position stays stable.

Manage the Power Cable

I connect the included power cable to the camera and route it toward the nearest indoor outlet. I keep the cable loose enough to avoid pulling on the camera, but I do not leave a large loop where someone could catch it. I use suitable cable clips to hold it against the wall or furniture.

I keep the Indoor Cam (2nd Gen) indoors and away from steam, moisture, extreme temperatures, radiators, vents, stoves, and other heat sources. I place the power adapter where air can circulate, and I avoid covering it with fabric or pushing it tightly behind furniture.

Test the View and Finalize Settings

I check the camera image from the Ring app, adjust the mount for full coverage, and remove areas that create unwanted alerts. I also verify notifications, recording settings, and privacy controls before finishing the installation.

Verify Live View Coverage

I open Live View in the Ring app and inspect the camera’s image from different parts of the room. I make sure the view includes doors, windows, or other areas I want to monitor without pointing directly at bright lights, windows, or heat sources.

I adjust the camera angle by hand until the image shows the right amount of floor and entry space. If I mounted the camera high, I check that the angle does not leave a large area hidden beneath the lens.

I also confirm that the power cable reaches the outlet without pulling on the camera. After making the final adjustment, I tighten the mount screws so the camera stays in position.

Fine-Tune Motion Detection

I open the motion settings in the Ring app and review the camera’s motion zones. I include the areas where a person may enter, while excluding places that could trigger repeated alerts, such as windows, fans, or busy walkways outside the room.

I walk through the monitored area to test detection from different directions. If the camera misses movement, I widen the zone or adjust the camera angle. If it detects too much activity, I narrow the zone rather than moving the camera unnecessarily.

I keep the camera indoors and away from heaters, vents, stoves, steam, and extreme temperatures. These conditions can affect the device and may create unreliable alerts.

Confirm Notifications and Recording

I trigger a test alert by moving through the selected motion zone. I confirm that my phone receives the notification and that the alert identifies the correct Ring camera.

I check the Ring app’s notification and recording settings. If I use a Ring subscription, I verify that motion events save correctly and that I can open a recorded event. Without a recording plan, I can still use available live features, but event storage may be limited.

I also test the privacy cover. When I close it, I confirm that it disables the camera’s audio, video recording, Live View, and motion detection. I leave the cover open only when I want the camera to monitor the room.

Frequently asked questions

Can I mount the Ring Indoor Cam 2nd Gen outdoors?
No. I recommend using it indoors only. Keep it away from steam, extreme temperatures, and heat sources such as radiators, stoves, and heater vents.

Can I mount it on a wall or ceiling?
Yes. I can mount the camera on either surface with its included mounting hardware. I should choose a stable location with a clear view and access to a power outlet.

How do I choose the right position?
I should place the camera where it can cover the intended area without pointing directly at bright lights or windows. I also need to keep the power cable safely secured and avoid locations where it could become a trip hazard.

Does mounting affect the camera’s features?
No. The camera still supports features such as two-way audio and remote viewing through the Ring app. After mounting, I should adjust the viewing angle and check the live feed.

Can I move the camera after mounting it?
Yes. I can remove it and install it in another suitable indoor location. I should update the camera angle and confirm that the power cable remains secure.

What should I check before drilling?
I should confirm the mounting surface, avoid hidden wires or pipes, and use the correct anchors for the wall or ceiling material. I should also make sure the camera remains within reach of the power cable.

Conclusion

I mount the Ring Indoor Cam (2nd Gen) where it can cover the needed area without pointing directly at bright lights or heat sources. I use a shelf or the included mounting hardware, depending on the room and viewing angle.

Before drilling, I check the live view in the Ring app and confirm that the power cable can reach a safe indoor outlet. I keep the camera away from steam, radiators, stoves, and other heat sources.

After mounting, I tighten the screws, adjust the camera angle, and test motion alerts, video, night vision, and two-way audio. I also use the manual privacy cover when I want to block the camera’s view.

These final checks help me keep the camera stable, powered, and positioned for useful indoor coverage.